# Inbound calls fail

**URL:** <https://forums.vitalpbx.org/t/inbound-calls-fail/4868>\
**Category:** VitalPBX\
**Created:** [January 12, 2025, 12:14pm UTC](https://forums.vitalpbx.org/t/inbound-calls-fail/4868 "2025-01-12T12:14:50Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![tdemeyer](https://forums.vitalpbx.org/letter_avatar_proxy/v4/letter/t/db5fbb/32.png) [@tdemeyer](https://forums.vitalpbx.org/u/tdemeyer)\
**Post date:** [January 12, 2025, 12:14pm UTC](https://forums.vitalpbx.org/t/inbound-calls-fail/4868/1 "2025-01-12T12:14:50Z")

</div>

I’m trying to configure a 1-number ‘trunk’ to our local VOIP provider. The number is/was working fine on a previous voip config (Fritzbox).

I defined the trunk with default settings. The PJSIP report shows a green status.

Outbound traffic over this connection works fine: I can dial out without any problem.

However, when I try to dial in, I get an automated message from the provider that the dialed number is not registered. When I power down the vitalpbx computer, this message stays the same, so I’m sure this message originates from the provider.

My Vitalpbx inbound rule is configured for “any DID/Any CID”, and has the same device I use for dialing out as its destination.

I was looking for a log file that could tell me more, but I cannot find anything usefull…  
Anybody who can help me solving this issue?

---

<div class="post-metadata">

**Author:** ![PitzKey](https://forums.vitalpbx.org/user_avatar/forums.vitalpbx.org/pitzkey/32/420_2.png) [@PitzKey](https://forums.vitalpbx.org/u/PitzKey)\
**Post date:** [January 12, 2025, 3:01pm UTC](https://forums.vitalpbx.org/t/inbound-calls-fail/4868/2 "2025-01-12T15:01:41Z")

</div>

Hello @tdemeyer,

Asterisk logs would normally be under `/var/log/asterisk/full`

However, I suggest first looking at the raw packets if the INVITE even hits your PBX. You can use a tool like `sngrep` [1] to monitor unencrypted SIP packets

[1] [SNGrep – VitalPBX Wiki](https://wiki.vitalpbx.org/wiki/troubleshooting/sngrep/)

---

<div class="post-metadata">

**Author:** ![tdemeyer](https://forums.vitalpbx.org/letter_avatar_proxy/v4/letter/t/db5fbb/32.png) [@tdemeyer](https://forums.vitalpbx.org/u/tdemeyer)\
**Post date:** [January 13, 2025, 9:50am UTC](https://forums.vitalpbx.org/t/inbound-calls-fail/4868/3 "2025-01-13T09:50:47Z")

</div>

OK, stupid mistake to start with… Forgot to open the inbound ports to the PBX…  
So I opened inbound UPD 5060-5061 and UDP 10000-20000 to the PBX

I now have a constant Busy signal when calling the number. Will try SNGrep as suggested…

---

<div class="post-metadata">

**Author:** ![system](https://forums.vitalpbx.org/uploads/default/original/1X/672b458a1d454755270c2c16adc5316b641c3c6a.png) [@system](https://forums.vitalpbx.org/u/system)\
**Post date:** [February 12, 2025, 9:51am UTC](https://forums.vitalpbx.org/t/inbound-calls-fail/4868/4 "2025-02-12T09:51:10Z")

</div>

Closed on February 12, 2025, 9:51am UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
